|
|
|
|
|
|
Frequently Asked Questions
- Can I install the system myself?
- I feel confident installing the
system myself. Where do I start?
- What are the blue connectors and how
are they used?
- Why are most of your controls embedded
in epoxy?
- How elaborate should I make the alarm
system?
- Which Deck Sensors should I use?
- What if I drop my key farb in the
water and cannot retrieve it?
- How long will the deck sensors
last?
- How long is the siren?
- Do I need to mount these L.E.D.s
(light emitting diodes)?
- What if I leave my boat for a long
time and there is no electrical hook up?
- Can I be notified if there is a
problem on my boat?
- Why should I buy a MarineGuard
Network system over another brand?
If you are comfortable making repairs on your boat, you should
have no difficulty. However, if you are doubtful, you should
have a professional do the installation.
First, you need to decide what sensors you want to use and what
control package fits your needs.
Then, you start by reviewing the operations manual of both
The Protector (CG1) and The Protector Deluxe (MG5).
Click here.
After you have reviewed the manuals, take a good look at your
boat and ask yourself, "Where is the power source and where do I
want to mount the control?" Caution, when deciding where
you want to install the control, make sure you leave enough wire
so you can remove the box and work in a comfortable position.
[The blue connectors are epoxy-filled crimps used to attach wire
to each other. The best marine practice is to solder and use
shrink-tubing with a sealant.
Epoxy is a great sealant. It prevents the electronic
components from becoming loose causing the system to fail.
Many years ago, we did not use epoxy. A system was
installed on a racing boat and, after its first run to the
Bahamas, some of the components became loose and the system
failed. Since we started to use epoxy, we have not had
this problem occur again.
All MarineGuard products are built to last.
Keep it simple. Whenever possible, use only Deck Sensors.
We also suggest you use the smallest number of sensors possible.
They work so well that most boats need 4 or less Deck Sensors.
If you want additional security components or you cannot use Deck
Sensors because you cannot get under the cockpit, keep the extra
components to a minimum.
For fiberglass decks on motor boats, use the DSE2.
For fiberglass decks on sailboats, use the ENHP2.
For steel decks with teak use the HPP2.
A replacement is readily available from us or any alarm
distributor. Also, it is suggested to install a concealed
switch on your boat to disarm system.
We presently have working sensors that were installed back in
1975.
All of our sirens have a good decibel level. Wind can cause
a siren's sound to be diminished. For this reason, we suggest
attaching spreader lights to your alarm system. These lights
will flash when the alarm is activated. Also, we recommend
using a monitoring system so that you are notified if you alarm
system is triggered.
We strongly advise you to install the LEDs. They tell you
whether you system is ready to be armed or is currently armed.
A flexible, rollup solar panel is available for powering the boat
alarm in this type of situation.
Yes. If you are in an area where there is good cell
coverage, then use a cell transmitter. If you trailer your
boat, have it on a mooring, or want to be able to track your boat,
we suggest using a cell transmitter with GPS capabilities. If
you are on a large lake, travel a distance offshore, or travel in an
area where cell coverage is weak or non-existent, we recommend
MarineGuard's satellite transmitter.
This is a good question. We have a very long tradition
in the security industry. Our reputation is sound and we
have a very loyal following of installers and customers.
Our Pulsors are the preferred sensor on large yachts to control
cameras and to initiate early warning. They are also
installed to protect historical boats.
In addtion, Sure Action Pulsors/MarineGuard Deck Sensors are
frequently used by our competitors. Sure Action is the
only manufacturer of Pulsors and Deck Sensors in the world.
Any boat alarm system that uses Deck Sensors (Pulsors) are using
Sure Action components.
Sure Action's Pulsors are widely used to protect historical
buildings at famous historical sights. They are used to
protect water towers, fire escapes, cat walks at mines, to
control lighting in home automation systems, and to protect
roofs.
Our alarm components are deliberately designed to be simple
to install and operate. With over 40 years in the security
industry, Sure Action (MarineGuard) strives for false-free alarm
equipment. Why use second best?
|
|
|
|
|
|
|
|
